HDX HDXBRSTK Use and Care Manual download pdf (Page 7)

Operation Continued)-( (Model#HDXFWS)

Nose (F)

Nose plate (E)

Nose scr ew (D)

Setting the air pressure

The amount of air pr essure required depends on the

size of the fasteners and the workpiece material.

Begin testing the depth of drive by driving a test nail

into the same type of workpiece material used for the

actual job. Drive a test fastener with the air pressur e

set at 90-95 psi. Raise or lower the air pressure to find

the lowest setting that will perform the job with

consistent results. It may be possible to achieve the

desired depth with air pr essure adjustments alone.

Adjusting the exhaust

The adjustable exhaust on the cap of the tool allows

users to direct the exhaust accor ding to operator

prefer ence. To adjust the direction, turn the exhaust cap

in the desired direction.

Loading Fasteners

Connect the tool to the air source.

Push down on the latch button (A). Pull back on the

magazine cover (B).

Load a clip of fasteners with the cr owns straddling the

magazine rail (C).

Push the magazine cover (B) forward until latch button

pops up.

Latch button(A)

Magazine

Cover(B)

WARNING: The tool may fire when it is first

connected to the air source. Always connect the

tool to the air source before loading fasteners to

prevent injury from unintended cycling. Always make

sure the tool’s magazine is empty at the beginning

of each work session, before connecting to an air

source.

WARNING: Keep the tool pointed away from yourself

and others when loading fasteners. Failure to do so

could result in possible serious personal injury .

WARNING: Use only fasteners r ecommended for use

with this tool. Fasteners not identified for use with this

tool by the tool manufactur er ar e able to result in a risk

of injury to persons or tool damage when used in this

tool.

WARNING: Never load fasteners with the workpiece

contact or trigger activated. Doing so could r esult in

possible serious personal injury .

Magazine Rail(C)

Operation Continued)-( (Model#HDXST9040)

HOMEDEPOT.COM

Please contact 1-800-514-6729 for further assistance.

Non-marring pad

The non-marring pad attached to the nose of the tool

helps prevent marring and denting when working with

softer woods.

WARNING: Disconnect the tool fr om the air source

before removing or replacing the non marring pad.

Failure to do so could result in serious personal

injury .

Firing the tool

The tool is specially designed for single sequential mode.

This mode requires the trigger to be pulled each time a

fastener is driven. The tool can be actuated by depressing

the Work Contact Element (WCE) (G) against the work

surface followed pulling the trigger (H).

The trigger must be released to reset the tool before

another fastener can be driven.

WARNING: Always know the operational mode of the

tool before using. Failure to know the operational

mode could result in death or serious personal injury .

WARNING: An improperly functioning tool must not be

used. Do not actuate the tool unless the tool is placed

firmly against the work place.

Trigger (H)

W ork contact

element (G)

W ork contact element (WCE)

Disconnect the air supply fr om the tool.

Remove all fasteners from the magazine.

Make sure the trigger and work contact element move

freely up and down without sticking or binding.

Reconnect air supply to the tool.

Depress the work contact element against the work

surface without pulling the trigger, the tool must not

operate. Do not use the tool if it operates without pulling

the trigger. Personal injury may result.

Remove the tool from the work surface, the work contact

element (WCE) must return to its original down position,

the tool must not operate. Do not use the tool if it

operates while lifted from the work surface. Personal

injury may result.

Pull the trigger and depress the work contact element

(WCE) against the work surface, the tool must not

operate.

Depress the work contact element (WCE) against the

surface, pull the trigger, the tool must operate.

WARNING: Make sure there is no fastener in

magazine before clearing a jam.

CAUTION: Check the operation of the work contact

element trip mechanism before each use. The WCE

must move freely without binding through its entir e

travel distance. The WCE spring (I) must return the

WCE to its fully extended position after being

depressed. Do not operate the tool if the WCE trip

mechanism is not operating pr operly . Personal injury

may occur.

Trigger

Spring (I)

1 2 3 4 5 6 7 8 9 10 11 12 ... 22 23

Comments to this Manuals

No comments

HDX HDXBRSTK Use and Care Manual Page 7

Comments to this Manuals